You are currently viewing How to Change Oil on a Motorcycle – A Step-by-Step Guide

How to Change Oil on a Motorcycle – A Step-by-Step Guide

Motorcycles are a fun way to get around, and they can be economical too! However, if you don’t know how to change the oil on a motorcycle, it can be a real pain. In this blog post, we will walk you through the process step-by-step. We’ll explain what you need to do and provide some helpful tips. So, whether you’re a beginner or an experienced mechanic, read on for all the information you need to change your motorcycle’s oil successfully!

Why should you change your motorcycle’s oil?

It’s essential to regularly change your motorcycle’s oil because it helps keep the engine clean and running smoothly. Over time, oil breaks down and becomes less effective at lubricating the engine parts. This can cause friction and wear, which can lead to severe damage. Changing your oil regularly will help prevent this from happening.

How often should you change your motorcycle’s oil?

Most motorcycle manufacturers recommend changing the oil every 3000-5000 miles. However, it’s a good idea to check your owner’s manual to be sure. Some bikes may need to change the oil more often, depending on how they’re used. For example, if you do a lot of stop-and-go riding in hot weather, you may need to change your oil more often.

What do you need to do before changing the oil?

Get the necessary tools and materials – You will need a few tools to change your motorcycle’s oil, including a wrench, an oil filter wrench, and a drain pan. You will also need some fresh oil and a new oil filter.

Park the motorcycle on a level surface – This will make it easier to drain the oil and prevents spills.

Warm up the engine helps the oil flow more easily and makes it less likely to spill.

Place a pan under the drain plug – This will catch the old oil as it drains out.

Remove the drain plug – Use your wrench to remove the drain plug from the bottom of the engine. Allow the oil to drain into the pan.

Remove the oil filter – Use your oil filter wrench to remove the old oil filter. Be careful not to touch the hot surface of the engine with your bare skin.

Install the new oil filter – Install the new oil filter and tighten it by hand.

Replace the drain plug – Put the drain plug back in and tighten it with your wrench.

Fill the engine with new oil – Pour fresh oil into the machine until it reaches the whole line on the dipstick.

Check for leaks – Start the engine and allow it to run for a few minutes. Then check for leaks around the drain plug and oil filter.

Clean up – Dispose of the old oil and filter properly. Wipe up any spills with a rag.

Now you know how to change your motorcycle’s oil! Be sure to follow these steps carefully the next time you need to do it.

K&N Motorcycle Oil Filter: High Performance, Premium
K&N Motorcycle Oil Filter: High Performance, Premium
9.7
  • HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
  • PROTECT YOUR ENGINE:  Synthetic-blend filtration media removes most harmful contaminants
  • EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
  • VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
Fram PH6017A Spin-On Full-Flow Oil Filter for Motorcycles
Fram PH6017A Spin-On Full-Flow Oil Filter for Motorcycles
9.5
  • Proven protection for up to 10,000 miles
  • Engineered for use with conventional or synthetic motor oil
  • A special blend of fibers and resin creates a proprietary filter media that captures 95% of dirt particles that can cause harmful engine wear
  • Designed for everyday drivers who perform frequent maintenance on their vehicles
  • 95% dirt-trapping efficiency
AHL 142 Oil Filter for Yamaha YFM350X Warrior 350 1987-2004(yellow)
AHL 142 Oil Filter for Yamaha YFM350X Warrior 350 1987-2004(yellow)
9.1
  • High performance design for outstanding filtration
  • Size:O.D. 38mm & Height 47mm
  • Replace Parts Number KN142 & HF142
  • Ideal for high-end synthetic motor oil and allow high oil flow rates
  • Quality Assurance!If you are not satisfied with our products,we accept all of the return,replacement or refund requests

Tips for keeping your motorcycle in good condition

Motorcycles are a lot of fun, but they also require a fair amount of maintenance. Here are a few tips to help you keep your motorcycle in good shape:

  • Check the oil levels regularly and change the oil when needed. This will help to keep the engine clean and running smoothly.
  • Inspect the tires regularly for signs of wear and tear. If the tread is getting low, it’s time to replace the tires.
  • Clean the chain regularly with a chain cleaner or brush. This will help to prolong the life of the chain and prevent it from rusting.
  • Suppose you ride in wet conditions; clean and lubricate the chain after each ride. This will help to prevent water from damaging the chain.

By following these simple tips, you can help to keep your motorcycle running smoothly for years to come.

Valvoline 4-Stroke Motorcycle Full Synthetic SAE 10W-40 Motor Oil 1 QT
Valvoline 4-Stroke Motorcycle Full Synthetic SAE 10W-40 Motor Oil 1 QT
9.7
  • Full Synthetic Formula Helps Maximize Power And Acceleration
  • Formulated To Provide Outstanding Wet Clutch Protection For Maximum Power Transfer And Smooth Shifting
  • Added Protection Against Harmful Deposits That Can Decrease Engine Performance
  • Excellent Wear And Corrosion Protection To Help Keep The Engine Performing Its Best
YamaLube All Purpose 4 Four Stroke Oil 10w-40 1 Gallon
YamaLube All Purpose 4 Four Stroke Oil 10w-40 1 Gallon
9.5
  • Yamalube OEM Factory 4 Stroke All Purpose Oil
  • Performance-Blend is Suitable for use in Motorcycles, ATVs, Side-by-Side Vehicles, and Scooters
  • Mineral Oil Provides Stable Clutch Performance and Strength to Protect the Engine from Wear and Tear
  • Oil Meets or Exceeds the JASO MA Requirements
  • Genuine OEM Yamaha Product
Castrol 06113 Power RS 5W-40 4-Stroke Motorcycle Oil - 1 Quart, (Pack of 6)
Castrol 06113 Power RS 5W-40 4-Stroke Motorcycle Oil - 1 Quart, (Pack of 6)
9.1
  • Formulated with Trizone technology to protect all 3 critical zones: engine, clutch and gearbox
  • Race derived technology for maximum engine acceleration
  • Extreme high temperature air-cooled performance and water-cooled engine performance
  • Excellent shear stability to prevent viscosity breakdown
  • Exceeds API SL and JASO MA-2

FAQs about How to Change Oil on a Motorcycle

Motorcycles require regular oil changes to keep them running smoothly. However, changing motorcycle oil can be different from changing the oil in a car. Here are answers to some frequently asked questions about how to change motorcycle oil:

How often should I change my motorcycle oil?

Depending on the make and model of your motorcycle, you may need to change the oil every 3,000 miles or every 5,000 miles. However, it’s always best to consult your owner’s manual for specific guidance.

What kind of oil should I use?

Motorcycles generally require particular types of oil, such as synthetic or semi-synthetic oils. Once again, consult your owner’s manual for specific recommendations.

How do I know when it’s time to change my oil?

One way to tell if it’s time to change your motorcycle oil is to check the color of the oil. If it appears dark or muddy, it’s time for a change. You can also check the oil level using the dipstick; if it’s low, that’s another sign that it’s time for an oil change.

Is it hard to change the oil in motorcycles?

No, it’s not hard to change the oil in motorcycles. You’ll need a few things: a new filter, some fresh oil, and a wrench to remove the drain plug. First, you’ll want to warm up the engine for a few minutes so the oil is nice and thin. Then you’ll find the drain plug – it’s usually on the bottom of the engine – and remove it with your wrench. Be careful of hot oil – use a drip pan to catch it. Let all the oil drain out, replace the drain plug and fill the engine with fresh oil. Finally, install the new filter, and you’re all set! Just remember to check your owner’s manual for specific instructions on your motorcycle.

Can I change my oil?

Yes! Changing your oil is relatively straightforward with a bit of time and the right tools. Just consult your owner’s manual before getting started, as there may be some specific instructions for your bike. And, of course, if you’re ever uncertain about something, it’s always best to take your bike to a professional mechanic.

Conclusion

So, there you have it. Changing the oil on your motorcycle is a pretty simple process if you have the right tools and follow these steps. Just be sure to dispose of the old oil properly and keep an eye on your bike’s fluid levels in the future to avoid any nasty surprises. Have you changed your motorcycle’s oil before? What was your experience like?

 

Rick

Motorcycle life fan for 30 years and team writer for MotorcycleAccident.org